Chargeur bas

EBERT TLS 55 ATV / Tele / 39,5to Nutzlast

Technical data for EBERT TLS 43 ATV special low loader:
* Permissible fifth wheel pressure: 19,000 kg
* Permissible axle pressure: 36,000 kg
* Permissible total weight: 55,000 kg
* Unladen weight according to DIN approx.: 15,500 kg
* Drop center length: approx. 6,650 mm + 4,000 mm
* Axle table length: 3,550 mm
* Outer width: 2,550 mm
* Loading edge/lower bed: approx. 200 mm - 350 mm
* Sliding table length: 500 mm
* Widening/lower bed to: 3050 mm
* Low bed/telescopic by: 4,000 mm
* B dimension: 13,300 mm
* Entire vehicle flame-spray galvanized, with epoxy resin primer and 2K paint finish
* Extra-wide signage at the front and rear with red/white boards
Wheels: 13 x Michelin 245 / 70 R 17.5 X MULTI T VB 143J/146F

Steering: TRIDEC DLS with Tritronic

Axles: 12,000 kg ? DLS independent suspension hydraulically steered and hydraulically sprung

Front high bed: * Side walls 600 mm high
* Angled corners at the front of the high bed
* Doors accessible from the outside in the left and right corners
* Lockable storage box with lid behind the bulkhead Height 600 mm, width 2,480 mm, depth 7,500 mm
* Spare wheel on the high bed, behind the partition wall on the right
* Stairs on the right-hand side to get from the low bed to the high bed at the front
* Hydraulic coupling for uncoupling on the left-hand side 6-fold Multi-Faster coupling
* 6 lashing positions 3,000 kg version on the outside of the high bed (drop lashing eyes)
* 2 lashing positions 5,000 kg version on top of the longitudinal strands (to the rear)
Low bed: * Climbing aids on the boom ? Extension
* Outer frame t=8 mm
* Lowbed can be telescoped by 4,000 mm and locked every 500 mm
* With sliding table, lockable every 250 mm
* 28 lashing positions 10,000 kg Exterior version in the outer frame
* 24 90 x 90 plug-in tubes, evenly distributed for low-bed extension to 3,050 mm
* 50 mm hardwood planks are placed between the extension tubes, 10 mm overhang
Raised bed at the rear: * Raised bed slanted to the front and perforated, for retrofitting ramp support profiles, using galvanized adapters
Cckkmcjls0
* Ramp support profiles (Altec) at the rear ? C - Rails
* 8 lashing positions 10,000 kg Exterior version on the high bed
* 6 lashing positions 5,000 kg version in the excavator trough
* 10 lashing positions 5,000 kg version with excess width in the outer frame
* Closure of the excavator trough at the front and rear with a wooden floor plate (insertable)
Electrics: * Use NATO coil, power comes from the towing vehicle
* Rotating beacon at the center rear
* LED side lights
* Standard rear light for upright mounting (LC5)
* Working lights on the high bed, for lighting the low bed
* Oversize signage at the front and rear for uncoupling control, sensor for fuse and pressure switch for the suspension
Air:
* Aluminum air tank 80 l
* TEBS modulator
* Locking pull-out left and right (valve on the side in the rear high bed)
* Double release valve
Hydraulics: Hydraulic system on the high bed for steering, suspension and detachable gooseneck
Accessories: * 2x 4 wooden planks as support for widening the low bed and intermediate table
* 2 safety wedges for uncoupling
* 4 wheel chocks

On request, we can make you a leasing or financing offer, Mr. Ebert (Tel.) will be happy to assist you, Further information can be found on our homepage, Subject to errors and prior sale!

L'annonce a été traduite automatiquement et des erreurs de traduction peuvent apparaître.